WiFi Mesh Testing Standard Based on Ministerial Decree 352 of 2024 and 12 of 2025

WiFi mesh uses communication technologies that operate within a specific frequency spectrum. This technology must meet the main requirements through a standard testing process to ensure its quality, security, and compliance with applicable regulations.

This standard WiFi mesh testing process is stated in the Ministerial Decree of the Ministry of Communication and Digital No. 352 of 2024 and No. 12 of 2025 which regulates various technical aspects, ranging from radio frequency, and transmit power, to testing methods.

Wireless technology, which is widely used in WiFi mesh devices must comply with this standard to be used legally in Indonesia.

New Regulations on WiFi Mesh Technology

This regulation covers radio frequency requirements, maximum transmit power, and testing for wild emissions (spurious emissions).

Ministerial Decree 352of 2024

The following are the standard specifications for Cellular Network:

E-ULTRA Operating Band	Uplink	Downlink	Dupleks Mode
1	1920 MHz – 1980 MHz	2110 MHz – 2170 MHz	FDD
3	1710 MHz – 1785 MHz	1805 MHz – 1880 MHz	FDD
5	824 HHz – 849 MHz	869 MHz – 894 MHz	FDD
8	880 MHz – 915 MHz	985 MHz – 960 MHz	FDD
28	703 MHz 748 MHz	758 MHz – 803 MHz	FDD
31	452,5 MHz – 457,5 MHz	462,5 MHz – 467,5 MHz	FDD
40	2300 MHz – 2400 MHz		TDD

Ministerial Decree 12 of 2025

The following are the standard specifications for WiFi:

Frequency Band	Output Power	Spurious Emission	Test Method
2400 – 2483,5 MHz	< 27dBm EIRP	EN 300 328	EN 300 328
5150 – 5250MHz	EIRP < 23 dBm	EN 301 893	EN 301 893
5250 – 5350MHz	EIRP < 23 dBm	EN 301 893	EN 301 893
5725 – 5825MHz	EIRP < 23 dBm	EN 300 440	EN 300 440

WiFi Mesh Testing Standard

Ministerial Decree 352 of 2024

WiFi mesh is carried out to ensure the device meets technical standards Ministerial Decree of the Ministry of Communication and Digital No. 352 of 2024. Here are some of the main points in the test:

• Electrical Safety: SNI IEC 60950-1:2016, SNI IEC 62368-1:2014, or IEC 62368-1; and/or other relevant IEC or SNI standards.
• EMC (Emission): SNI IEC CISPR 32:2015, IEC CISPR 32, or ETSI EN 301 489-50 according to ETSI EN 301 489-1
• EMC (Immunity): The Testing Method for immunity requirements is under the provisions in the SECOND Dictum of this Ministerial Decree.

Ministerial Decree 12 of 2025

WiFi mesh testing is carried out to ensure the device meets technical standards Ministerial Decree of the Ministry of Communication and Digital No. 12 of 2025. Here are some of the main points in the test:

• Electrical Safety: SNI IEC 60950-1;2015 or the more recent, SNI IEC 62368-1;2013 or the more recent, IEC 60950-1; IEC 62368-1; and/or other relevant IEC or SNI standards.
• EMC (Emission): ETSI EN 301 489 and/or ETSI EN 301 489-17; IEC CISPR 32; and/or SNI CISPR 32: 2015 or the more recent.
• EMC (Immunity): The Testing Method for immunity requirements is under the provisions in the THIRD Dictum of this Ministerial Decree.
• RF Output Power, Channel Bandwidth, Power Spectral Density, Spurious Emissions, and Out-of-band Emissions: ETSI EN 302 567 (lowest version is 2.1.1)

WiFi Mesh Certification Process in Indonesia

For WiFi mesh devices to be used legally in Indonesia, certification from DJID is required. Here are the steps to get it:

Pre-testing the device

Before official testing, the device must be pre-tested first using measuring equipment such as a spectrum analyzer.

This helps ensure devices meet technical standards before being tested in authorized laboratories.

Testing at an official laboratory

After passing the pre-testing, the gadget will be sent to an assigned official research facility to experience testing according to the guidelines stipulated in the Ministerial Decree of the Ministry of Communication and Digital No. 352 of 2024 and No. 12 of 2025.

Issuance of certificates

After the device passes testing, an official certificate will be issued by DJID. This certificate is a requirement to market the device legally in Indonesia.

Tips to ensure standards compliance

• Learn the latest regulations: Make sure you understand every detail of the Ministerial Decree of the Ministry of Communication and Digital No. 352 of 2024 and No. 12 of 2025, including technical requirements and test methods.
• Perform pre-testing: Before official testing, perform pre-testing to ensure the device meets standards. If you don’t have a measuring instrument, use the DJID certification service which provides pre-testing services.
• Counsel a master: If this is your to begin with time looking for certification, consider utilizing the administrations of experienced DJID certification administrations.